UK Buell Enthusiasts Group
https://www.ukbeg.com/forum/

2008+ ECM connectors
https://www.ukbeg.com/forum/viewtopic.php?f=8&t=4355		 Page 1 of 1
Author:  gunter [ 11 Jan 2010 08:19 ]
Post subject:  2008+ ECM connectors
Does somebody know which connectors are used for the new ECM? Chances are, I might get one for bench tests, so a pinout would be helpfull also.
Author:  pash [ 11 Jan 2010 09:14 ]
Post subject:  Re: 2008+ ECM connectors
I have it in the Electrical manual for my 1125. If Kev doesn't beat me to it, I'll dig the info out when I get home from work. :D
Author:  kevmean [ 11 Jan 2010 12:32 ]
Post subject:  Re: 2008+ ECM connectors
Oooooh a challenge lOl lOl
I'll maybe not give you what you want though lOl

ECM J1(11A)(GY) connector
2= clutch switch
4=throttle position sensor
5=barometric pressure sensor
6=Manifold absolute pressure sensor
8=neutral switch
9=coolant temperature input
10=fuel pressure sensor
13=vehicle speed sensor
14=intake air temp sensor
15=serial data receive
16=serial data transmit
17=bank angle sensor
18= crank position sensor+
19=sensor ground #3
20=idle air control motor
21= idle air control motor
22=idle air control motor
23=idle air control motor
24=5V sensor power#1
25=5V sensor power #2
26=crank position sensor -
27= sensor ground #1
28=sensor ground #2
29= CAN low
30= CAN high
31=O2 sensor front
32=O2 sensor rear
34= sidestand sensor

J2 (10A)(BK) connector

2=fan#1 (right)
3= fan #1 (right)
7= starter enable
8= system ground #4
9= ignition switch
10= active intake solenoid
16= system ground #3
17= battery
18=fan #2 (left)
19=auxilliary relay ground
24= sytem ground #2
25= front ignition coil
26= fan #2 (left)
27=fuel pump output
28=fuel pump output
29= front injector output
30= rear injector output
31= rear ignition coil
32=rear ignition coil
33= system ground #1
34= front ignition coil
Author:  pash [ 11 Jan 2010 12:34 ]
Post subject:  Re: 2008+ ECM connectors
Nice work Kev. Now we need someone with a late XB to fill in the gaps - I would think there is the Adaptive Muffler Control pin out data that is outstanding.

Any description of what the connecter is? Maybe in the parts book?
Author:  gunter [ 11 Jan 2010 12:36 ]
Post subject:  Re: 2008+ ECM connectors
Great, thanks a lot, that's definitely what I wanted to know! :worthy: All I need now is the connector manufacturer and type.
Author:  kevmean [ 11 Jan 2010 12:48 ]
Post subject:  Re: 2008+ ECM connectors
OK parts book lists them as
connector, 34pin (black) part number Y0219.4a8
connector, 34pin (grey) part number Y0232.4A8
will see if i can find any more info ;)
Author:  kevmean [ 11 Jan 2010 12:50 ]
Post subject:  Re: 2008+ ECM connectors
ecm part number for reference is Y0152.1AM
Author:  kevmean [ 11 Jan 2010 12:54 ]
Post subject:  Re: 2008+ ECM connectors
Just found this
ECM (black) 34-place Amp (Tyco)
ECM (grey) 34-place Amp (Tyco)

;) hope this helps .......made buying the manual seem worthwhile now lOl
Page 1 of 1 All times are UTC
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/