Save yerself a loada pain and just throw it in the bin
| UK Buell Enthusiasts Group https://www.ukbeg.com/forum/ |
|
| exhausted https://www.ukbeg.com/forum/viewtopic.php?f=8&t=1154 |
Page 1 of 1 |
| Author: | obelix the gaul [ 19 Jun 2009 23:36 ] |
| Post subject: | exhausted |
Hi, I have a quill exhaust that id like to fit to my 06 ulysses... could someone point me in the right direction, as to any other mods. i should carry out to the bike, to make sure it runs correctly with this pipe..?? also, should i unplug the servo. which operates the valve in the OE exhaust, or just remove the cable ?? Thanx. |
|
| Author: | Maz [ 19 Jun 2009 23:38 ] |
| Post subject: | Re: exhausted |
Save yerself a loada pain and just throw it in the bin
|
|
| Author: | 03 [ 20 Jun 2009 07:48 ] |
| Post subject: | Re: exhausted |
Quote: I have a quill exhaust that id like to fit to my 06 ulysses... The local tip is waiting for the Quill. If you're lucky, you might find a mug to buy it off you but it's unlikely to be a member from here I'm afraid.
could someone point me in the right direction |
|
| Author: | pash [ 20 Jun 2009 10:11 ] |
| Post subject: | Re: exhausted |
Read the How To section regarding the AMC motor (you are a wise wizard Maz  ):viewtopic.php?f=17&t=12 |
|
| Author: | mcrbuelligan [ 20 Jun 2009 16:21 ] |
| Post subject: | Re: exhausted |
do not fit the quill under any surcumstances - i had a quill and the outlet end cap came off while i was on the motorway- and going on your front wheel at 70 was not a fun place to be - your better just takin out the servo cable for a easy exhaust mod to your stock exhaust and remapping your ecm and kit a k&n - far better and the bike will run better i found the quill had the noise but no go- but doin the above the bike has more mid |
|
| Author: | Adam [ 20 Jun 2009 17:15 ] |
| Post subject: | Re: exhausted |
Just to add to the tales of woe, I've had 1st hand dealings with Quill cans (on other peoples bikes) and you really will be doing yourself a favour if you throw it in the bin. If you want to pass on the misery, stick it on Ebay. I've seen the complete back section blow out of them, I hate to think what would've happened to my mate if it had gone under his wheel in a bend 
|
|
| Author: | 03 [ 20 Jun 2009 17:25 ] |
| Post subject: | Re: exhausted |
It's a bit sad really, they're a north west based company near-ish to me and they're making bits for bikes. I can't knock that because I get sick of seeing all these websites flogging german and italian made stuff sometimes at crazy assed prices. I wish more british co's made stuff, but not crap stuff like Quill seem to make. And even sadder than that, there's been folk queuing up from here to give them sound, free advice. But they will not listen. 
|
|
| Author: | obelix the gaul [ 22 Jun 2009 12:50 ] |
| Post subject: | Re: exhausted |
Thanx everyone for your feedback.... erm, anyone wanna buy a quill exhaust, 50 quid... will make a nice ornament for your garage !!. |
|
| Author: | 03 [ 22 Jun 2009 14:35 ] |
| Post subject: | Re: exhausted |
obelix the gaul wrote: Thanx everyone for your feedback.... erm, anyone wanna buy a quill exhaust, 50 quid... will make a nice ornament for your garage !!. Try Ebay  
|
|
| Author: | Adam [ 22 Jun 2009 15:38 ] |
| Post subject: | Re: exhausted |
Bung the end with clay, it'd make a very nice vase 
|
|
| Author: | mcrbuelligan [ 22 Jun 2009 20:37 ] |
| Post subject: | Re: exhausted |
mine is currently a dust collector |
|
| Author: | pash [ 30 Jun 2009 18:55 ] |
| Post subject: | Re: exhausted |
obelix the gaul wrote: Thanx everyone for your feedback.... erm, anyone wanna buy a quill exhaust, 50 quid... will make a nice ornament for your garage !!. http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... SS:GB:1123 
|
|
| Author: | mcrbuelligan [ 01 Jul 2009 17:30 ] |
| Post subject: | Re: exhausted |
£280 your havin a laugh |
|
| Page 1 of 1 | All times are UTC+01:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|