Check out. Demon Tweeks website for a Goodrich inline banjo fitting hydraulic brake light switch, I think I got mine from there.
| UK Buell Enthusiasts Group https://www.ukbeg.com/forum/ |
|
| re : rear brake light switch for X1 2001 https://www.ukbeg.com/forum/viewtopic.php?f=11&t=22881 |
Page 1 of 1 |
| Author: | Babybadger [ 03 Jan 2018 01:18 ] |
| Post subject: | re : rear brake light switch for X1 2001 |
Hi guys, Its back in the UK! yay! and guess what, started with 11 month old fuel in it straight away and ran up to temp beautifully......, now for UK MOT....... Headlight lense, sorted..... Indicators.....sorted...... Rear Brake Light switch - shot...... Any ideas for a replacement? Also is there anywhere that does UK licence plates with a reflector built in? Thanks in advance....... |
|
| Author: | gusm2 [ 03 Jan 2018 05:33 ] |
| Post subject: | Re: re : rear brake light switch for X1 2001 |
Check out. Demon Tweeks website for a Goodrich inline banjo fitting hydraulic brake light switch, I think I got mine from there.
|
|
| Author: | pash [ 03 Jan 2018 06:00 ] |
| Post subject: | Re: re : rear brake light switch for X1 2001 |
This’un https://rover.ebay.com/rover/0/0/0?mpre ... 1895263391 Leave the standard one in place and put this in place of the banjo bolt... |
|
| Author: | Bonzo [ 03 Jan 2018 08:16 ] | ||
| Post subject: | Re: re : rear brake light switch for X1 2001 | ||
Babybadger wrote: Also is there anywhere that does UK licence plates with a reflector built in? I just get one from Halfrauds, or wherever, stick it on a bit of plastic and rivet it to the plate, as below. OK, so it's not a UK plate, and it's not a Buell or an X1, but you get my drift. I've done the same on my Enfield in the UK for the same reason you're doing it. I forgot about it until the examiner pointed it out and suggested I nip out sharpish, buy one and just stick it on the bottom of the plate, mind you the plate at the time was about 2 ft x 1 ft 
|
|||
| Author: | Babybadger [ 03 Jan 2018 10:45 ] |
| Post subject: | Re: re : rear brake light switch for X1 2001 |
pash wrote: This’un https://rover.ebay.com/rover/0/0/0?mpre ... 1895263391 Leave the standard one in place and put this in place of the banjo bolt... Thanks as always Mr. Pash.....its ordered........ |
|
| Author: | Graeme1203 [ 03 Jan 2018 11:26 ] | ||
| Post subject: | Re: re : rear brake light switch for X1 2001 | ||
Easiest way of dealing with the reflector is to purchase the cheap small round ones (for pennies) and fix to the numberplate , available as bolted or self adhesive eg https://www.amazon.co.uk/MOTORCYCLE-STI ... B01N6OHJNH
|
|||
| Author: | gusm2 [ 03 Jan 2018 14:51 ] |
| Post subject: | Re: re : rear brake light switch for X1 2001 |
pash wrote: This’un
https://rover.ebay.com/rover/0/0/0?mpre ... 1895263391 That's the fella cheaper than DT too Leave the standard one in place and put this in place of the banjo bolt... |
|
| Author: | Babybadger [ 04 Jan 2018 18:04 ] |
| Post subject: | Re: re : rear brake light switch for X1 2001 |
Thanks all, also on the look for at least one (dont know why i bother with them cant see anything.....) mirror to go on the drivers side , pair would be nice, better than stock but must be cheap, until I get back to pick the originals up in Tenerife. Any idea of thread pitch and size? Recommendations? |
|
| Author: | pash [ 04 Jan 2018 19:52 ] |
| Post subject: | Re: re : rear brake light switch for X1 2001 |
Some bar end mirrors Sir? https://rover.ebay.com/rover/0/0/0?mpre ... 2228504468 |
|
| Page 1 of 1 | All times are UTC+01:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|