You need Albert race headers and a Pipeworx race muffler along with my header mount and stainless flanges
| UK Buell Enthusiasts Group https://www.ukbeg.com/forum/ |
|
| X1 Lightning Exhaust Can https://www.ukbeg.com/forum/viewtopic.php?f=11&t=22437 |
Page 1 of 1 |
| Author: | Andycovs [ 22 Jun 2017 20:35 ] |
| Post subject: | X1 Lightning Exhaust Can |
Exhaust race can silencer or similar wanted for my 2001 X1 lightning.Miron,Supertrapp etc Must be be in excellent condition please. |
|
| Author: | Maz [ 22 Jun 2017 20:51 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
You need Albert race headers and a Pipeworx race muffler along with my header mount and stainless flanges
|
|
| Author: | pash [ 22 Jun 2017 21:22 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
|
|
| Author: | DaveH [ 22 Jun 2017 21:32 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
Or if your funds don't go to the full dogs bollox set up as recommended by Maz. There is this on eBay http://www.ebay.co.uk/itm/Buell-x1-Vanc ... SwhvFZB5Mb ........Dave |
|
| Author: | Maz [ 22 Jun 2017 22:21 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
 yeah, right 
|
|
| Author: | deepsix [ 22 Jun 2017 22:58 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
Maz wrote: :roll: yeah, right Exactly, do it right, do it once 
|
|
| Author: | Graeme1203 [ 22 Jun 2017 23:04 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
Firstly, is there a difference between a V&H for a M2, S1 and as X1 ? (Other than 2 and 2.5) Secondly, please tell me that's the going rate for a very used V&H, looks like I now have a pension fund 
|
|
| Author: | TOPGUMM [ 22 Jun 2017 23:14 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
they all fit the same, the headers differ. £100 would be about the cost for secondhand v+h with elbow. The carbon ones are dodgy. Go for an albert headers plus pipeworx etc. £600+ ish if you have it |
|
| Author: | Maz [ 23 Jun 2017 00:06 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
Quote: £600+ ish if you have it Albert headers circa 450 Pipeworx muffler 300 Header mount 50 ....so, circa 800 quid plus stainless flanges at 40 quid and if you dont already have the 01 wishbone mount, add another 180 quid.....plus gaskets, studs, nuts, ret rings, etc......plus fitting if you aint up to it 
|
|
| Author: | x1glider [ 23 Jun 2017 06:30 ] |
| Post subject: | Re: X1 Lightning Exhaust Can |
Too bad you're not in the US as I have a full D&D for the X1 for a couple hundred. Taking up space as wall art. |
|
| Page 1 of 1 | All times are UTC+01:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|