| UK Buell Enthusiasts Group https://www.ukbeg.com/forum/ |
|
| master wanted https://www.ukbeg.com/forum/viewtopic.php?f=11&t=20279 |
Page 1 of 1 |
| Author: | buellboy1200 [ 13 May 2015 21:13 ] |
| Post subject: | master wanted |
hi can any help with were to buy a rear master cylinder for my 2002 buell m2 |
|
| Author: | pash [ 13 May 2015 21:22 ] |
| Post subject: | Re: master wanted |
If it helps, there's a rebuild kit, part number H0040.F, costs about £16 from Riders of Bristol with UKBEG discount. |
|
| Author: | buellboy1200 [ 13 May 2015 21:30 ] |
| Post subject: | Re: master wanted |
hi pash put a new kit in but no good bin trying to bleed this for hours all i get is air so.fed up with it just want to get back on the road . thanks tho |
|
| Author: | Maz [ 13 May 2015 21:40 ] |
| Post subject: | Re: master wanted |
Assuming you fitted the kit correctly, did you fit/anneal new copper washers on the banjos ? |
|
| Author: | DaveH [ 13 May 2015 21:43 ] |
| Post subject: | Re: master wanted |
Have you removed the caliper off its mounting and held it above the seat. I had to do this when i goodridged the origional caliper and when i fitted the rear beringer. I fannied around with a syringe trying to reverse bleed and tried using the conventional method to no avail and my thought m/c was goosed. Once i'd lifted the caliper it bled in 10 mins. HTH. |
|
| Author: | pash [ 13 May 2015 21:49 ] |
| Post subject: | Re: master wanted |
Or push the piston in on the caliper to force the air back through the master cylinder. If you lived close I'd come and do it for you. I find it very therapeutic... |
|
| Author: | Adam [ 13 May 2015 21:55 ] |
| Post subject: | Re: master wanted |
DaveH wrote: Have you removed the caliper off its mounting and held it above the seat. I had to do this when i goodridged the origional caliper and when i fitted the rear beringer. I fannied around with a syringe trying to reverse bleed and tried using the conventional method to no avail and my thought m/c was goosed. Once i'd lifted the caliper it bled in 10 mins. HTH. 
|
|
| Author: | Adam [ 13 May 2015 21:57 ] |
| Post subject: | Re: master wanted |
pash wrote: Or push the piston in on the caliper to force the air back through the master cylinder. I've never thought of doing that  I'll give it a try next time  
|
|
| Author: | Matron [ 13 May 2015 22:19 ] |
| Post subject: | Re: master wanted |
I was going to suggest a PM to Finmows  
|
|
| Author: | Jill Brown [ 13 May 2015 22:45 ] |
| Post subject: | Re: master wanted |
Matron wrote: I was going to suggest a PM to Finmows Lol...I was thinking exactly the same thing... 
|
|
| Author: | rik [ 13 May 2015 22:49 ] |
| Post subject: | Re: master wanted |
Adam wrote: pash wrote: Or push the piston in on the caliper to force the air back through the master cylinder. I've never thought of doing that I'll give it a try next time Just be prepared for spillage at the reservoir... it may be violent so cover it as well as wrap it! |
|
| Author: | Bonzo [ 14 May 2015 00:04 ] |
| Post subject: | Re: master wanted |
Jill Brown wrote: Matron wrote: I was going to suggest a PM to Finmows Lol...I was thinking exactly the same thing...
|
|
| Author: | pash [ 14 May 2015 06:03 ] |
| Post subject: | Re: master wanted |
rik wrote: Adam wrote: pash wrote: Or push the piston in on the caliper to force the air back through the master cylinder. I've never thought of doing that I'll give it a try next time Just be prepared for spillage at the reservoir... it may be violent so cover it as well as wrap it! Slowly with more mechanical sympathy than a caressing robot... |
|
| Author: | Finmows [ 14 May 2015 19:28 ] |
| Post subject: | Re: master wanted |
Bonzo wrote: Jill Brown wrote: Matron wrote: I was going to suggest a PM to Finmows Lol...I was thinking exactly the same thing... 
|
|
| Page 1 of 1 | All times are UTC+01:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|