| UK Buell Enthusiasts Group https://www.ukbeg.com/forum/ |
|
| S1 / S3 RH switchgear / throttle assembly https://www.ukbeg.com/forum/viewtopic.php?f=11&t=11193 |
Page 1 of 2 |
| Author: | pash [ 31 May 2011 22:35 ] |
| Post subject: | S1 / S3 RH switchgear / throttle assembly |
In reality I only want the white plastic cable guide... Let me know if you can help. Thanks |
|
| Author: | pash [ 01 Jun 2011 19:06 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
|
|
|
| Author: | Nutah [ 01 Jun 2011 19:09 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Pash is the switchgear made for any other bike ? i.e. jap stuff , maybe still available |
|
| Author: | Adam [ 01 Jun 2011 19:25 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Yam R6 throttle tubes fit the housing, so maybe they have the same guide too? Didn't Beef have this problem some years ago? |
|
| Author: | pash [ 01 Jun 2011 19:50 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
I.. sniff.. tried to.. sniff sniff.. Araldite it, but.. sniff sniff.. but it broke again when I put it together.. Need to.. sniff.. remain focussed.. |
|
| Author: | Nutah [ 01 Jun 2011 19:58 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
pash wrote: I.. sniff.. tried to.. sniff sniff.. Araldite it, but.. sniff sniff.. but it broke again when I put it together.. Need to.. sniff.. remain focussed.. then stop sniffin the glue dude |
|
| Author: | Jill Brown [ 01 Jun 2011 20:00 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Nutah wrote: pash wrote: I.. sniff.. tried to.. sniff sniff.. Araldite it, but.. sniff sniff.. but it broke again when I put it together.. Need to.. sniff.. remain focussed.. then stop sniffin the glue dude 
|
|
| Author: | Nutah [ 01 Jun 2011 20:03 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Pash can you use steel pipe , car brake pipe maybe , to form it from ? |
|
| Author: | daywalker [ 01 Jun 2011 22:30 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Adam wrote: Yam R6 throttle tubes fit the housing, so maybe they have the same guide too? Didn't Beef have this problem some years ago? Lots of people on oldskoolsuzuki use R6 throttle tubes to make a quick action throttles so it might fit but might not be what you want. |
|
| Author: | Beef [ 02 Jun 2011 00:01 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
I did indeed have the same problem years ago..... I caught the prob a bit sooner than Pash, filled the worn groove with Araldite and filed it smooth. This lasted probably 10000miles then the araldite came un-stuck and jammed the throttle wide open   luckily it was a favourite bit of road  I then sourced a set of later M2 switchgears from Tubbs and they plugged straight into the loom and have the bonus of a much smoother throttle action 
|
|
| Author: | Dunno [ 02 Jun 2011 03:32 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Don't 1990s Triumphs have the same switchgear as Buells? |
|
| Author: | mojomick [ 02 Jun 2011 07:47 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
If you can sketch it Nick, maybe I can make it out of black Delrin or Nylon 66. 
|
|
| Author: | pash [ 02 Jun 2011 08:09 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Thanks for the offer, most kind of you... Think I have found a source of brand new ones. Will know by the weekend... Had considered fashioning one from brass... |
|
| Author: | Nutah [ 07 Jun 2011 12:58 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
any luck Nick ? |
|
| Author: | pash [ 07 Jun 2011 13:02 ] |
| Post subject: | Re: S1 / S3 RH switchgear / throttle assembly |
Still looking... 
|
|
| Page 1 of 2 | All times are UTC+01:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|