It is currently 29 Mar 2024 12:26

All times are UTC




Post new topic  Reply to topic  [ 11 posts ] 
Author Message
 Post subject: 1125CR high bar diameter
PostPosted: 05 Jun 2010 20:04 
Offline
User avatar

Joined: 03 Apr 2010 20:11
Posts: 63
Location: Lincolnshire
Hi all can anyone tell me what diameter barends the 1125CR high bar conversion bars take ?

_________________
BUELLSRCOOL !!


Top
PostPosted: 06 Jun 2010 11:47 
Offline
User avatar

Joined: 06 May 2009 21:29
Posts: 1479
28.75mm


Top
PostPosted: 06 Jun 2010 19:15 
Offline
User avatar

Joined: 06 May 2009 21:29
Posts: 1479
Sorry, I need to spend more time reading posts properly, not sure what diameter the bore of the tubes is and I can't check for you either as bike is in mcr h/d for a while yet.

Andy


Top
PostPosted: 06 Jun 2010 21:30 
Offline
User avatar

Joined: 06 May 2009 14:19
Posts: 1356
Current ride: Cagiva Raptor 650
Location: Scottish Borders
What's wrong with your bike mate?

As for the bars I assume that there 7/8th"

_________________
Norrie.


Top
PostPosted: 07 Jun 2010 00:14 
Offline
Site Admin
User avatar

Joined: 15 Apr 2009 17:17
Posts: 8629
Location: Manchester
Quote:
What's wrong with your bike mate?


:shut:

_________________
Mithered ta death.
92 MB
96 S2T
98 S1W
00 M2
01 X1
03 P3
10 CR


Top
PostPosted: 07 Jun 2010 12:44 
Offline
User avatar

Joined: 03 Apr 2010 20:11
Posts: 63
Location: Lincolnshire
19mm is the answer

_________________
BUELLSRCOOL !!


Top
PostPosted: 07 Jun 2010 16:58 
Offline
User avatar

Joined: 06 May 2009 17:28
Posts: 7253
Current ride: 1991 RS1200 westwind
The bars are stepped inside though so to fit the R&G barends i had to reduce the diameter of the wedgethat expands the plug as it wouldn't fit in the smaller diameter further in the bars ;)

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.


Top
PostPosted: 07 Jun 2010 17:14 
Offline
proff. patpending
User avatar

Joined: 06 May 2009 20:20
Posts: 14705
Current ride: Victoria Sponge
Location: Bristol - Gateway to all things good
Welcome back Kev

_________________
08 Specialized Langster


Top
PostPosted: 07 Jun 2010 17:53 
Offline
User avatar

Joined: 06 May 2009 17:28
Posts: 7253
Current ride: 1991 RS1200 westwind
I was here about 10pm last night ;) .......just too tired to post a lot though lol

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.


Top
PostPosted: 09 Jun 2010 10:29 
Offline
User avatar

Joined: 07 May 2009 11:00
Posts: 509
Current ride: xb12s 1125cr 1125r
Location: PORTSMOUTH
My R&G fitted ok Kev just fiddly on the left bar but the small fitment went in ok :yup:



Mind you i AM 21 STONE SO CAN PUSH IT LOL

_________________
A12 XBS, B 15 OUT !!


Top
PostPosted: 09 Jun 2010 17:27 
Offline
User avatar

Joined: 06 May 2009 17:28
Posts: 7253
Current ride: 1991 RS1200 westwind
Blackrag123 wrote:
My R&G fitted ok Kev just fiddly on the left bar but the small fitment went in ok :yup:



Mind you i AM 21 STONE SO CAN PUSH IT LOL


Is your's a CR or R ?.........the bar end itself fitted in but the diameter of the wedge was far to big to go down the reduced section of the bar on mine.

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.


Top
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 11 posts ] 

All times are UTC


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited